收藏本站
NCP1028
The bridge power dissipation is 330 2 /3.018 Meg =
36 mW in nominal high-line operation. Figure 29b
simulation result confirms our calculations.
Figure 30 describes signal variations during a brown-out
when V CC reaches V CC(ON) , ensuring a clean startup
sequence. As in fault mode conditions, the startup source
is activated on and off and self-supplies the controller in a
Dynamic Self-Supply (DSS) mode.
condition. Please note that output pulses only reappear
Figure 30. Signal Evolution During a Brown-Out Condition
Depending on input surge tests, it might be necessary to
wire a filtering capacitor between BO and GND (close to
the circuit) to avoid adversely triggering the internal latch
(unless this is a wanted feature) when the pulse train
appears.
Latchoff Protection
There are some situations where the converter shall be
fully turned-off and stay latched. This can happen in the
presence of a secondary overvoltage (the feedback loop is
drifting) or when an overtemperature is detected.
Secondary monitoring is usually implemented when the
coupling between auxiliary and power windings does not
lead to a precise primary detection. Due to the addition of
a comparator on the BO pin, a simple external circuit can
lift up this pin above VLATCH and permanently disable
pulses. The V CC needs to be cycled down below 3.5 V
typically to reset the controller.
http://onsemi.com
17
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
NCP1216AFORWGEVB BOARD EVAL NCP1216A 35W
NCP1351LEDGEVB EVAL BOARD FOR NCP1351LEDG
NCP3065BBGEVB BOARD EVAL NCP3065 MR16 BOOST
NCP3066SCBCKGEVB EVAL BOARD FOR NCP3066SCBCKG
NCP5005GEVB EVAL BOARD FOR NCP5005G
NCP5006EVB EVAL BOARD FOR NCP5006
NCP5030MTTXGEVB EVAL BOARD FOR NCP5030MTTXG
NCP5602EVB EVAL BOARD FOR NCP5602
相关代理商/技术参数
NCP1028P065G 功能描述:电流型 PWM 控制器 NCP1028 65 KHZ RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
NCP1028P100G 功能描述:电流型 PWM 控制器 NCP1028 100 KHZ RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
NCP1028PL065R2G 功能描述:交流/直流开关转换器 ANA 1 FREQ GULLWING RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel
NCP102MBGEVB 功能描述:电源管理IC开发工具 NCP102 4W MOTHERBRD EVB RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
NCP102SNT1G 功能描述:低压差稳压器 - LDO LDO LINR REG CONTRL RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
NCP1030 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Low Power PWM Controller with On-Chip Power Switch and Startup Circuits for 48V Telecom Systems
NCP1030_06 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Low Power PWM Controller with On−Chip Power Switch and Startup Circuits for 48V Telecom Systems
NCP10301 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:AC-DC Offline Switching Controllers/Regulators